Technical Guide for Live Production

When designing signal pathways for robotic camera installations—whether outfitting a broadcast studio, worship center, sports venue, or corporate auditorium—production engineers face an architectural choice: single-cable IP workflows via NDI or legacy point-to-point baseband infrastructure via SDI.

While 3G/12G-SDI provides deterministic, zero-latency uncompressed video streams, it requires tri-cable runs (video, power, and serial control). Conversely, Network Device Interface (NDI) consolidates bi-directional video, tally metadata, Power over Ethernet (PoE+), and camera control into a single Cat6 Ethernet run.

Architectural Comparison: Single-Cable Cat6 vs. Tri-Cable Legacy Runs

Understanding physical cable topology highlights the labor and materials involved in pulling runs across long distances.

Single-Cable NDI Workflow (Cat6 Ethernet):
[ PTZ Camera ] <=== (Single Cat6 / PoE+: Video, Power, VISCA, Tally) ===> [ Managed GbE Switch ] ===> [ Host vMix / TriCaster ]

Legacy SDI Workflow (Tri-Cable Run):
[ PTZ Camera ] <--- (RG6 Coax / BNC: Video Stream) -------------> [ SDI Frame Grabber / Switcher ]
               <--- (18/2 AWG Copper Cable: 12V DC Power) -------> [ Power Supply Brick ]
               <--- (RS-232 / RS-422 Cable: VISCA Control) ------> [ Hardware Joystick Controller ]

The Single-Cable NDI Advantage

Modern NDI PTZ cameras (utilizing Full NDI or NDI|HX3) leverage standard Power over Ethernet (PoE+ 802.3at / PoE++ 802.3bt). A single Cat6 run carries:

  • Uncompressed/Low-Latency Compressed Video (Up to 4K60)
  • Bidirectional Control Protocol (VISCA-over-IP / NDI Control)
  • Real-time Tally Metadata (Program Red / Preview Green)
  • DC System Power (Up to 30W–60W delivered via the network switch)
  • Bi-directional Audio & Intercom Signals

The Legacy SDI Infrastructure Footprint

A traditional SDI PTZ run requires three distinct cables per camera head:

  1. RG6 Coaxial Cable (75 Ohm BNC): Carries uncompressed baseband video (3G-SDI for 1080p60 or 12G-SDI for 4K60).
  2. 18/2 Low-Voltage Power Wire: Delivers 12V DC power from a central power distribution box or local wall wart transformer.
  3. RS-422/RS-232 Shielded Twisted Pair: Transmits serial VISCA, Pelco-D, or Panasonic control signals back to a hardware controller.

Infrastructure Cabling Cost Breakdown

The financial difference between NDI and SDI extends far beyond initial camera head pricing. Total cost of installation depends heavily on conduit capacity, cable material costs, and technician termination labor.

Cabling Cost & Labor Comparison Matrix

Estimates based on a 4-camera installation requiring 200-foot cable runs per camera (800 total feet of run length).

Cost CategorySingle-Cable Cat6 NDITri-Cable SDI (SDI + Power + Serial)
Bulk Cable Material~$0.30 – $0.50 / ft (Cat6 CMR/CMP)~$1.20 – $2.50 / ft (Belden 1694A + 18/2 + RS422)
Connector HardwareCat6 RJ45 Keystone Jacks (~$5 / drop)BNC Crimp Plugs + Power Blocks + DB9 (~$25 / drop)
Cable Pulling Labor1 Cable per Camera (Fast installation)3 Cables per Camera (Heavy conduit fill)
Power DistributionIntegrated Managed PoE+ Switch (~$400)12V DC Multi-Channel Power Box (~$250)
Serial Patch Hardware$0 (Handled via Ethernet IP routing)RS-422 Distribution Block / Breakout Box (~$350)
Estimated Install Cost~$150 – $250 per camera drop~$450 – $750 per camera drop

Network Bandwidth Planning Tables

Deploying NDI PTZ systems requires allocating sufficient network backplane and port bandwidth across managed switches.

+-----------------------------------------------------------------------------------+
|                        NDI Transport Bandwidth Profiles                           |
| Full NDI (1080p60):   [================ 125-150 Mbps ================]           |
| NDI|HX3 (1080p60):     [==== 40-80 Mbps ====]                                      |
| NDI|HX2 (1080p60):     [== 12-20 Mbps ==]                                          |
+-----------------------------------------------------------------------------------+

Protocol Bandwidth Requirements per Camera Stream

Video Format & ResolutionFull NDI (SpeedHQ Intra)NDI|HX3 (Low-GOP H.264/HEVC)NDI|HX2 (Standard GOP)
1080p @ 30fps~100 Mbps~30 Mbps~10 Mbps
1080p @ 60fps~150 Mbps~60 Mbps~15 Mbps
4K UHD @ 30fps~200 Mbps~80 Mbps~25 Mbps
4K UHD @ 60fps~250 – 300 Mbps~110 – 140 Mbps~40 Mbps

Multi-Camera Network Topology Guidelines

To prevent packet congestion, network switches must be provisioned according to total throughput:

  • 4x 1080p60 Full NDI Cameras: Requires 600 Mbps sustained bandwidth. A standard Managed 1GbE PoE+ switch is sufficient.
  • 8x 4K60 Full NDI Cameras: Requires 2.4 Gbps sustained bandwidth. Requires a switch with a 10GbE SFP+ uplink trunk to the vMix/TriCaster host PC.
  • 8x 4K60 NDI|HX3 Cameras: Requires ~880 Mbps sustained bandwidth. Can run reliably across a standard Gigabit network backbone.

Signal Transport Latency Benchmarks

Latency dictates whether a camera signal can be routed to venue IMAG (Image Magnification) screens without introducing lip-sync offset.

Glass-to-Glass Signal Transport Latency:

Baseband 3G/12G-SDI:  [= 5-10 ms =]  --> Frame-Accurate (Zero Compression)
Full NDI (High-BW):   [== 16-33 ms ==] (1-2 Frames) --> Suitable for IMAG
NDI|HX3:              [==== 60-80 ms ====] (3-4 Frames) --> Stream / Broadcast Only
NDI|HX2:              [======== 120-200 ms ========] (7-12 Frames) --> Remote Web Feed

Test Scenario: Measured from physical light input at the camera lens to pixel output on a reference monitor.

Transmission ProtocolGlass-to-Glass LatencyFrame Delay (@ 60fps)Suitable for Stage IMAG?
3G-SDI / 12G-SDI5 – 10 ms< 0.5 FramesYes (Ideal)
Full NDI (High Bandwidth)16 – 33 ms1 – 2 FramesYes
NDI|HX350 – 80 ms3 – 5 FramesBorderline (Requires testing)
NDI|HX2120 – 200+ ms7 – 12+ FramesNo (Noticeable lip-sync lag)

Installation Decision Tree

                                 [ Architectural Decision ]
                                             |
                  +--------------------------+--------------------------+
                  |                                                     |
       Are you pulling new cabling through                   Is instant zero-latency (<10ms)
       conduit and need fast setup?                           IMAG or ST 2110 required?
                  |                                                     |
                  v                                                     v
      +------------------------+                           +-------------------------+
      |  Deploy Single-Cable   |                           |  Deploy Baseband 3G/12G |
      |     Cat6 NDI System    |                           |      SDI Infrastructure |
      +------------------------+                           +-------------------------+

Choose NDI PTZ Infrastructure if:

  • You are retrofitting an existing building where running single Cat6 cables through walls or drop ceilings reduces installation costs.
  • You need bi-directional tally, VISCA control, power, and video delivered over a single cable.
  • You operate a software-based switcher ecosystem (vMix, OBS Studio, TriCaster, Wirecast).
  • You require rapid field setup for mobile flypacks, temporary sports venues, or pop-up studios.

Choose SDI PTZ Infrastructure if:

  • Your production environment feeds large stage IMAG screens where video latency must stay strictly below 10 ms to prevent lip-sync issues.
  • You operate within legacy master control rooms built around hardware switchers (Blackmagic ATEM, Ross, Sony) with dedicated BNC routing switchers.
  • You are pulling long single-cable runs exceeding 330 feet (100 meters) without network switch hops.

Frequently Asked Questions

Can an NDI PTZ camera output SDI simultaneously?

Yes. Most professional NDI PTZ cameras feature simultaneous outputs. A camera can output baseband 3G/12G-SDI directly to an IMAG video wall while streaming a Full NDI or NDI|HX3 feed over Cat6 Ethernet to a live production workstation.

What happens if a Cat6 Ethernet cable run exceeds 100 meters (328 feet)?

Ethernet standards cap Cat6 copper runs at 100 meters (328 feet). To extend an NDI camera run beyond 100 meters, insert an inline PoE+ powered network switch as a repeater, or convert the Ethernet connection to single-mode optical fiber via SFP+ transceivers.

What network switch features are required for NDI PTZ cameras?

NDI network switches must be Managed Layer 2 or Layer 3 switches supporting PoE+ (802.3at), IGMP Snooping (v2/v3) to manage multicast traffic, and Quality of Service (QoS) prioritizing video packets over general data traffic. Unmanaged desktop switches should be avoided for multi-camera NDI setups.